www.android-online.ru РазработчикиOBD Scantech

Приложения разработчика OBD Scantech в Android Market

Критерий сортировки:
1-2 из 2
Иконка для Car Gauge Lite OBD2 3.61.09

Car Gauge Lite OBD2 (v. 3.61.09)

OBD Scantech опубликовал приложение 2013-01-17
(обновлено 2015-04-20)

You can create custom gauges and the application will communicate with the vehicles ECU at the 16 Pin OBD II diagnostic connecter. Most of the OBD II connector location should be under the Steering Wheel Compartment. ELM 327 Bluetooth Adapter is required to make this application work. Car Gauge Lite not only can be exciting with gauges, it is a Professional Scan Tool.  Do you have a check engine light on? Do you want to know the Readiness Status will pass for a Smog Inspection? Do you want to check the functionality of the Sensors and determine the status of the Mode 5/6 Emission On-board Test(Some Models may not support it)?  Car Gauge Lite will show you.  


***Car Gauge Pro available <a href="https://play.google.com/store/apps/details?id=Scantech.CarGaugePro&hl=en">Car Gauge Pro</a>

(See information below for the hardware type requirement.)  

Vehicle computer system have multiple signal protocols and ELM 327 supports many of them.  Currently, the following protocols are supported by the app and MUST be an OBD II Compliant Vehicle.


[Protocols Supported]

* VPW - 1996-2004 Year (GM vehicles)
* PWM - 1996-2004 Year (Ford vehicles)
* ISO 9141(Slow) - 1996-2004 (Chrysler, European, and Asian vehicles)
* KWP 2000(Slow/Fast) - 1996-2004 (Chrysler, European, and Asian vehicles)
* CAN (11/29 Bit) - (2004 and Newer)


[Car Gauge Lite Supports the Following with Limited Views]

[OBD II Generic]
* Mode 1 - Analog/Digital Gauges (160/215 Generic PIDS)
* Mode 1 - List View (220 Generic PIDS)
* Mode 2 - Freeze Frame Data
* Mode 3 - Read Current Faults
* Mode 4 - Clear Faults
* Mode 5 - O2 Sensor Test Result (Non CAN Bus)
* Mode 6 - On-board Test Result
* Mode 7 - Read Pending Faults
* Mode 8 - Evaporative System Leak Test
* Mode 9 - Vin, Performance Tracking Data, ECU Name, Calibration and Verification ID
* Mode A - Read Stored Faults
* I/M Readiness Status
* O2 Sensor Location

Disclaimer Notice:  
Do not attempt to enter information or adjust your device while driving.  Failure to pay full attention to the operation of your vehicle could result in death, serious injury, or property damage. You assume total responsibility and risk for using your device with this app.

The App is setup for importing background, needle skins and gauge skins from SD card.  You can download it from the website.

MINIMUM VM HEAP SIZE (24m).  Anything lower may cause the application to force close while adjusting gauge size.


HARDWARE REQUIREMENT:  ELM 327 (Clone Type) Bluetooth Adapter.
Vendors Type: CHX, OBDII, Vgate Bluetooth Device tested OK.

Бесплатно
Иконка для Elm 327 Terminal 1.18

Elm 327 Terminal (v. 1.18)

OBD Scantech опубликовал приложение 2012-12-28
(обновлено 2012-12-28)

A simple program that will communicate with your ELM 327 OBD II Bluetooth adapter.  The ELM 327 Bluetooth Adapter is a Device that connects directly to your Vehicles 16 Pin OBD II diagnostic connector. Choose one of many commands from the list or you may type in a valid command.  

HARDWARE REQUIREMENT:  ELM 327 (Clone Type) Bluetooth Adapter.
Vendors Type: CHX, OBDII, Vgate Bluetooth Device tested OK.

Disclaimer Notice:

Do not attempt to enter information or adjust your device while driving.  Failure to pay full attention to the operation of your vehicle could result in death, serious injury, or property damage. You assume total
responsibility and risk for using your device with this app.

Requirement: Android 2.0 or higher for Bluetooth to function properly.

Бесплатно
Страница:  1